KTJO 4×4 Tailgate Lock 3rd Gen Tacoma – Review

KTJO 4x4 Power Tailgate Lock For Tacoma & Tundra

8.9
Average Score
  • Build Quality 8.0
  • Fitment 9.0
  • Customer Support 10.0
  • Ease of Install 7.5
  • Value - Is it worth it? 10.0
Easy Upgrade To Secure The Bed Of Your Truck – Install & Review

Unfortunately, our Tacomas do not come with a power-locking tailgate. The KTJO 4×4 tailgate lock kit aims to solve this issue and keep the contents of your bed safer! KTJO 4×4 prides itself on having many plug-and-play options for the Tacoma, Tundra, 4Runner, etc.; this kit is no exception.

While it’s not a fool-proof way to keep your bed secure, controlling a lock on your tailgate is a vast improvement over having nothing at all. At the very least, it will hopefully make would-be thieves skip over your truck.

What’s Included

3rd Gen Tacoma Power Lock Tailgate

Kit Contents

  • (1) Plug-and-Play Harness
  • (1) Tailgate Wire Harness
  • (1) Integrated Body Wire Harness
  • (1) Locking Actuator
  • (1) Bolt-N-Lock Bracket 
  • (1) Locking Rod
  • (1) Hardware Package
  • (2) Dual Wire Harness Protectors
  • Zip Ties

All of the hardware that you’ll need for installation is included. This plug-and-play kit requires no modifications to your truck to function properly.

Installation

KTJO 4x4 Power Tailgate Lock Installation Tools - DIY Install Guide

Tools Required (not included):

Installation is very straightforward. However, routing the new wiring will likely take longer than installing the locking actuator.

Step 1. Assemble The Actuator

Remove 3rd Gen Tacoma Tailgate Panel Cover For Tail Gate Lock Install

Initially, we need to undo the #30 Torx bolts holding the tailgate cover on. Then, set these off to the side with the tailgate cover.

Having a matching driver will make this go much faster!

KTJO 4x4 Tailgate Lock Actuator For Tacoma

Now, it’s time to attach the bracket to the new actuator. This is done with two bolts, two nuts, one bracket, and the actuator itself.

KTJO 4x4 Power Tailgate Lock DIY Installation Guide

After that is done, bolt the locking rod onto the black tip of the actuator. Grab your bolt and use a 9mm wrench or socket to tighten it. Do not over-tighten, however.

Step 2. Install Actuator Into Tailgate

Aftermarket Power Tailgate Lock For Tacoma

First, we need to remove the two 10mm bolts holding the OEM camera in place. (Don’t worry—the camera won’t move!)

How To Install A Power Tailgate Lock For 3rd Gen Tacoma

Next, place the actuator and bolt it in securely with the 10mm bolts you just removed. Once that is done, you can now remove the #15 Torx screw from the OEM tailgate lock.

Once that is removed, gently lift the black tab on which the lock is sitting.

KTJO 4x4 Tailgate Lock

The actuator’s new locking rod will slide over the black tab, and the OEM lock will slide back onto the tab.

Step 3. Route Wiring Harness

KTJO 4x4 Locking Tailgate Harness Wiring Guide

Now, the not-so-fun part! We need to move the harness from the tailgate to the truck’s passenger-side kick panel.

KTJO 4×4 provides replacement tailgate plastic grommets for a clean, factory-looking install! Plug the green into green and blue into blue, and you’re ready to start routing the harness.

I followed their installation guide and removed the clip on the left side of the tailgate near the actuator to tape my wiring tightly to the factory harness. Having this loose also gives you a little more wiggle room when routing the wiring.

Tailgate Lock Wiring Harness Routing

Use your flathead screwdriver to push the clip in on the wiring harness. Once that first one is out, route your wiring like factory and carefully clip it back into place.

Next, you’ll need to repeat for the bedside. This one is a little more tricky due to the lack of room to work with. I released the clip near the bedside grommet to give more play in the harness. This made it way easier to work with.

KTJO 4x4 Tailgate Lock For Tundra & Tacoma

Once this harness is poking out of the tailgate, we need to get it over to the bedside and through the new grommet.

Routing 3rd Gen Tacoma Tailgate Wire Harness

Place some electrical tape to keep the harnesses together when going to the grommets.

Step 4. Route Harness Under Truck

Routing Wires For Tailgate Lock

Next, we must route the harness up the passenger side to the kick panel inside the cab.

Route Wiring Into 3rd Gen Tacoma Cab - Rubber Grommet

This is super easy; just follow your existing harness and keep the wiring tight with zip ties along the way. You’ll see a large wiring harness going through a grommet into the cab. Pull this down and there is a small amount of tape that can be removed to slide your new wiring through.

Passenger Side Wiring Harness 3rd Gen Tacoma

Run the new wiring through the white factory clips to keep everything nice and neat. You can see where the wire loom is heading towards the right side.

Connect KTJO 4x4 Harness To Factory Wire Harness

Once you are at the kick panel, remove the plug pictured above. Next, plug in the KTJO 4×4 harness and connect the factory plug to the female end of the new harness.

You should be all set! Replace the kick panel after getting all the wiring cleaned up.

Final Thoughts

3rd Gen Tacoma Tailgate Lock Review

My first impression of this kit was that everything was very well packaged, and the instructions on their site were super clear. Everything was truly plug-and-play, and I had no issues with installation.

The actuator is not too loud when you hit the lock button on your key fob, which is always a plus! Overall, this kit is well worth the price!

If you need additional guidance or pictures for the installation, refer to the link under required tools at the beginning of the installation section.

Subscribe
Notify of
guest

2 Comments
Newest
Oldest Most Voted
Inline Feedbacks
View all comments
Chris J
Chris J
1 year ago

Thanks for this review. Can the tailgate still be unlocked with the key with this setup?

2
0
Questions or Comments?x
()
x