Brite Box 3rd Gen Tacoma Review

Anytime Brite Box - Independent Fog Lights & High Beam Controller for 3rd Gen Tacoma

Use Your High & Low Beams + Fog Lights Anytime

Whether you are an off-road enthusiast or a daily commuter, it is crucial to have adequate lighting when driving in the dark. Nighttime driving conditions can be very dangerous when there is poor visibility.

I’m sure most of us have had experiences where that poor visibility almost caused, or did cause, some kind of accident. Maybe you were driving down the highway and a deer ran out in front of your truck, causing thousands of dollars in damage. Maybe you were doing a trail run at night and you didn’t see that rock or log until it was too late.

Before you go out and spend the big bucks on lightbars or ditch lights, I’d recommend checking out the Brite Box Anytime from Aspire Auto Accessories. For around $100, the Brite Box gives you the ability to utilize both your high beams and your fog lights at the same time, using all of the lighting you have at your disposal. For whatever reason, the factory wiring harness does not allow for the operation of the high beams in conjunction with the fog lights.

This means you lose out on a lot of your near visibility when using your high beams. Personally, I don’t understand the logic but thankfully there’s a simple solution. This relatively straightforward modification will give you a brighter and ultimately safer driving experience after the sun goes down.

Find It Online

Features & Specs

Brite Box Anytime High Beam, Low Beam & Fog Light Controller

The Brite Box is a device that can increase your safety on dark roads. As I mentioned, most vehicles limit the functionality of your forward-facing lights. Ultimately, this can leave you with blind spots while using your high beams.

While the high beams are certainly beneficial, losing the ability to see near the front and sides of your vehicle could leave you susceptible to not seeing an object or animal until it’s too late. With certain makes and models, it’s even worse, using the high beams turns off the low beams as well as the fog lights.

The various models give you varying degrees of control over your high beams, low beams and fog lights. This setup is available for all 2nd & 3rd Gen Tacomas and can be installed in about 30 minutes or less.


  • Brite Box: Keep your low beams ON with high beams
  • Brite Box w/ Fog Light Control (FLC): Keep your low beams AND foglights ON with high beams
  • Brite Box Fogster: Keep your fog lights ON with high beams
  • Brite Box Anytime: Turn your fog lights ON & OFF with effect switch or OEM style push switch (works with high beams)

Although there are four options, not every make, model or trim have all four options available for purchase. It all depends on exactly which vehicle you own and what you’re looking to achieve.

As mentioned in the title, I’ll be covering the Anytime model which gives the user absolute full control.


Brite Box Anytime for Toyota Tacoma

Tools & Materials

  • Utility Knife
  • Needle Nose Pliers
  • 10mm Socket
  • 12mm Socket
  • Phillips Head Screwdriver
  • Flashlight

The installation is very straightforward, so if this is the first modification you make, it’s simple to do and won’t take too much time.

Step 1. Engine Bay Mounting

Mounting Brite Box Anytime in Engine Bay - 3rd Gen Tacoma

The Brite Box kit comes ready to plug and play. Start by cleaning the driver’s side of the engine bay frame with the provided wipe to ensure a clean surface for the adhesive to stick.

You do have the option of screwing the box into the frame, but with such strong adhesive backing, I trusted that it would hold just fine. I placed mine between the fuse box and the back of the engine bay. It is important to make sure that wherever you place the box, that all the wires still reach where they need to connect.

I recommend testing out the spacing before you permanently adhere the unit into the engine bay.

Step 2. Run Fog Light Wire

Routing Brite Box Anytime Wires to Fog Lights - 3rd Gen Tacoma

When you receive your kit, you’ll notice that everything is labeled clearly so you’ll know exactly where everything goes.

After the box is in place in the engine bay, feed the fog light wire along the side of the engine bay, beside the battery, and down behind where the fog light is located.

Step 3. Connect Fog Light Harness

Connecting Brite Box Anytime to Fog Light Harness on Toyota Tacoma

It is possible to connect the fog light harness without removing the grill and radiator deflectors from the front of the vehicle. Use a flashlight to locate the existing wiring for the fog lights. Reach down into the cavity behind the fog lights and disconnect the driver’s side fog light from the wiring harness.

Locate the new wire coming from the Brite Box and connect the male end (blue arrow) to the driver side fog light female end (red arrow). Connect the female end of the harness (green arrow) and connect it to the male end of the wire you disconnected from the fog light (yellow arrow).

You will only need to do this on the driver’s side.

Step 4. Expose Firewall Grommet

Running Wires into Cab for Brite Box Anytime

Inside your truck, on the driver’s side, remove the floor trim plate on the door frame by pulling up to detach all of the clips. Next, remove the plastic trim on the left side of the footwell. It covers the wiring and interior fuse box.

You’ll need to unscrew one Phillips head screw located above the footrest pad and then pull it towards the center console to pop out the clips. You’ll be able to see the bunch of wires coming through the firewall. Press back the insulation around it as best you can as it’s pretty stiff.

Step 5. Feed Wire Through Grommet

Running Wires Through Firewall Grommet on Toyota Tacoma

Once you have everything exposed, cut an approximately .5″ slit into the grommet. Cutting a slit instead of making a hole will allow your wire to come through but still keep a good seal.  Back in the engine bay, run the wire down to the other wiring seen in the firewall and get the end of the wire as close to the slit in the grommet as possible.

Then from inside the cab, stick the needle nose pliers through the slit and grab a hold of the wire. Once you have the wire with the pliers, slowly pull it into the cab. I got it far enough into the grommet so that I could reach through and grab farther back on the wiring to avoid pulling the adapter off of the end.

This was definitely the most difficult part for me, especially doing it alone. Make sure not to pull too hard as you’ll risk pulling the adapter off of the wires!  Alternatively, taping the harness to something sharp, like a coat hanger, and pushing it through the grommet would work as well.

Step 6. Remove Lower Dash

How to Remove Lower Driver's Side Dash on 3rd Gen Toyota Tacoma

Note: The instructions below are for installing the switch on the left side of the dash. If you need to install it in the middle of the dash, then you will need to remove the dash trim around the head unit as well.

Next, you will need to remove the lower portion of the dash under and around the steering wheel column. There are two Phillips head screws and one 10mm bolt along with several clips holding it in place. Once the screws and bolt are removed, grab the dash cover near the steering column (green line) and pull it straight away from the dash.

Hopefully, that will detach several clips and you’ll see where the remaining clips are located so you can remove them completely. If not, keep pulling until you get a couple of the clips to release. There are some switches still connected to the wiring behind it, so the dash trim will hang by those wires.

Step 7. Run Wire To Switch

Installing Switch for Brite Box Anytime for Toyota Tacoma

Take the wire that you fed through the grommet and feed it through any of the openings in the framework behind the dash cover.

You’ll want to do this so that the wiring and plug for the switch do not affect the dash cover clipping back into place.

Step 7. Install & Connect Switch

Switch for Brite Box Anytime

I went with a tall OEM style switch and I still had the stock blank location for that size on the left side of my dash.

You will remove the blank cover by releasing the tabs from the back and pushing the cover through the front.

Brite Box Anytime Detailed Installation Guide on 3rd Gen Tacoma

Then, making sure the new switch is oriented correctly, place it into the opening until you hear it click into place. Connect the wire you ran in behind the dash to the wiring on the switch.

Reattach the dash cover along with the two screws and one bolt. I had to really work on the clips around the lower airbag for it to be flush again.

Step 8. Connect To Power

Connect Brite Box to Battery with In-Line Fuse

Now that all of the wiring is hooked up, remove the nut on the positive terminal of the battery with the 12mm socket, then place the ring on the positive wire from the Brite Box onto the terminal, and reinstall the nut.

Finally, add the provided fuse into the slot on the positive wire from the Brite Box. You will then want to test to make sure that all your lighting turns on correctly and that your new switch controls the fog lights while your high beams are on.


Below you can see the comparison between just using your high beams and using the unit to utilize your high beams and fog lights. I wanted to show what it looks like from the driver seat with the added light output.

High Beams

3rd Gen Tacoma High Beam Output

High Beams & Fog Lights

3rd Gen Tacoma Output with Brite Box Anytime Output - High Beams, Low Beams, Fog Lights

Final Thoughts

Lifted Cement 3rd Gen Tacoma with Brite Box Anytime

When it comes to a lighting upgrade, it doesn’t get much easier than the Brite Box Anytime. Amazingly, they’ve made their kit completely plug-and-play so you don’t have to worry about cutting or splicing any wires. Just get them into place, plug them in and you’re good to go.

Regardless of where you drive, being able to have full control of your forward-facing lighting will make your drive much safer. This little kit can quickly and cheaply help illuminate the night by utilizing lights you already have! I’d recommend the Brite Box Anytime if you live in an area where you constantly have to worry about animals crossing the road at night and you’re frequently using your brights.

Lifted Cement 3rd Gen Tacoma with TRD Pro Grille & Brite Box Anytime

I’d also recommend it if you are an avid off-roader because it adds another option for lighting up your path without needing to find a new location for more lights. They have multiple options for the switch used with the Anytime kit, I chose to go with the OEM style switch and I love it.

It’s great quality, it’s backlit, and it looks like it was meant to be on the dash. All in all, it is a really well-designed product that is useful for virtually every type of driver.

Notify of

Oldest Most Voted
Inline Feedbacks
View all comments
1 year ago

1. My main objective is to have the fog lights on when my high beams are on, but what happens if my auto-high-beam switch is activated, will the fog’s turn off with the high-beams when the windshield light sensor detects oncoming traffic/light?
2. During regular operation (auto-high-beam switch off), does turning the high-beams on automatically activate the fogs if the fogs arent on with the light stalk?
3. During regular operation (auto-high beam switch off), if the fog lights are on using the light stalk, and the high-beams are on, does turning the high-beams off automatically turn off the fogs?

2 years ago

Will this allow me to turn on my foglights with the headlights off?
Will I retain the use of the fog switch on the headlight stalk?

Questions or Comments?x