Black Ops Offroad Anytime Locker For 3rd Gen Tacoma – Install & Review

3rd Gen Tacoma Doing Donuts With Anytime Rear Locker

Manufacturer: Black Ops Offroad MSRP: $249
9.0
Average Score
  • Build Quality 9.0
  • Fitment 9.5
  • Customer Support 9.0
  • Ease of Install & Instructions 8.0
  • Value - Is it worth it? 9.5
Simple Mod To Use Your Factory E-Locker In 4-Hi Or 2WD

Have you ever been in an offroad situation where you wished you could activate your factory e-locker without being in 4-Lo? Maybe you wanted to do some donuts in the snow… With the Black Ops Offroad Anytime Locker, you can lock your rear differential in 4-Hi or even 2WD.

This simple plug-and-play wire harness gives you full control over your rear end. With it, you’ll have more fun with your truck than ever before (like doing donuts).

Note: Adding this kit will disable your OEM button.

Reminder: Locking your differentials on dry pavement can damage them, only use this feature on loose or uneven terrain.

Factory Lockers In Tacomas

Factory E-Locker Button 3rd Gen Tacoma

Most Tacomas come with an open rear differentials. However, certain models (especially for 2016-2023), came with an electronic one from the factory. This applies to the TRD Off-Road and TRD Pro trims. It is typically only able to be engaged in low range gearing and at a low speed. This is mainly done with the intention of protecting the rear end from inappropriate use or activation that can result in damage. The typical use case scenario is for bad traction off-road.

This mod also works with a lower volume trim for the 3G, the SR5 Trail Edition – which also came with a locker from factory.

“Anytime” Modification

3rd Gen Tacoma 8.75" Rear Differential With OEM E-Locker

This mod is used to bypass any factory protocols and allows you to engage your locker whenever you need, regardless of the mode your truck is in.

But where is this most useful? The answer is two parts. One, you can use it in high speed situations in 2WD or 4-Hi where you might be travelling on a loose gravel road, a large incline, or in the sand (especially deep sand). Or like I mentioned earlier – you want to do some donuts in the snow. Less applicable, but still fun and nice to have, haha.

How Do They Work?

3rd Gen Tacoma On Devil's Staircase, Broken Arrow Trail

Unless you’re an electronic wizard and have the ability to splice factory harnesses (not for the inexperienced), there was no immediate and easy way to add this function. Sure, if you dig deep enough, someone tried and was successful. Or worst case, they had issues and error codes or a non-functioning locker.

Now, with the kit I’m highlighting, you can easily bypass the limitations set by Toyota. In this case, it involves adding a new wire harness and a switch to control everything. It really is plug and play and gives you full manual control.

Things To Consider

3rd Gen Tacoma Overlanding

As with any mod, you have to think about the risks. The factory setup is built that way for a reason, mainly to protect your truck from improper use and damage. Now this kit has been shown to be safe, but you’re still responsible for using it the right way. Engaging in the wrong setting can cause problems or expensive repairs. Depending on the situation, a dealer might try and use it as an excuse in a situation where a warranty claim comes up.

To clarify, I am not talking down or badly about the product, but educating you on the proper usage – which applies to anything. Although you could shift from drive to reverse on the highway, certainly doesn’t mean you should. It’s just common sense. Use good judgement and do your research, everything will be just fine. Plenty of people have done something like this, whether it’s a DIY or a tested kit like this one.

That said, the team at Black Ops has been testing and selling their units for years, and at the time of publishing, it’s ~$20-30 cheaper than the alternatives.

Installation

Anytime Locker by BlackOps Offroad

Tools Required

  • Panel pry tool (included with the kit)
  • 3/8″ or 1/4″ Ratchet
  • 8mm & 10mm socket
  • Phillips head screwdriver

Step 1. Disconnect Battery

Disconnecting Negative Battery Terminal

First, disconnect your battery by removing the negative battery terminal connection with a 10mm socket or wrench. Since we will be dealing with electronics, doing this will protect your system.

Step 2. Remove Trim Pieces

Removing Passenger Side Kick Panel

On the passenger front compartment, (4) plastic trim pieces need to be removed to access the bolts holding the glove box. As seen in the photo above, the first trim piece is at the base of the door. This piece comes off by gently prying upward.

Passenger Side Kick Panel 3rd Gen Tacoma

Next is the kick panel seen above. At the top of the floor mat, you can see a small stud on the kick panel that has a plastic thumb screw. Remove this thumb screw and pry the panel towards the center of the truck.

Removing Tacoma Dash Trim

The third trim piece can be removed using the supplied pry tool. After removing that, you can access the fourth trim piece (seen just to the left of the pry tool in the photo above).

The fourth trim piece is just held in with small clips. Gently pry the last panel back towards the passenger seat and it will come off.

Step 3. Remove Glove Box

Removing Tacoma Knee Air Bag

With all the plastics removed, we can pull out the passenger’s knee airbag to expose a few 10mm bolts securing the glove box. The knee airbag has (3) bolts to remove, (1) on the left and (2) on the right. When removing the airbag, be careful not to damage the yellow wire. I did not unplug my airbag and laid it off to the side during the installation.

3rd Gen Tacoma Glove Box Removal

The glove box will have (5) 8mm bolts to remove, (2) at the bottom, and (3) at the top. The two top bolts can be accessed inside the glove box with the door open. Once the bolts are removed, pull back on the glove box and pull it out of the truck.

Step 4. Connect Harness

E-Locker Harness Behind Dash

With the glove box out, pictured above is the view into the guts of your dash. In the center of the photo are components of your AC system, and to the right of that is the group of wires we need to focus on. This group of wires has three vertical sections with the center section being the 4WD module we will be connecting the plug-and-play harness to.

4WD/Locker Control Harness

The 4WD module has two plugs that need to be disconnected. The Black Ops harness has two male and two female ends that match the connectors. Connect it between the module and your Tacoma’s wire harness.

Before putting the glove box back together, reconnect the negative battery cable to test that everything is working. Once you have tested that there are no issues and the truck is functioning properly, reassemble the glove box and trim pieces.

Step 5. Install Switch

Anytime Locker Switch Mounting

Finally, there is a long control wire from the harness you can run to wherever you want to install the button. I ran this wire through the dash, over to the driver’s side, and installed the switch into the factory panel left of the steering wheel.

Final Thoughts

BlackOps Offroad Anytime Locker Review

Overall, the installation was not very difficult – it just takes a little time with all of the bolts and screws.

Not only is it awesome being able to do proper donuts in a Tacoma, but engaging the rear locker in any drive mode is a major upgrade. Activating it is as easy as pressing the new button and the backlight on the switch will flash until everything is engaged. Once it is activated, the backlight will stay solid.

If you want to fully unleash your Tacoma’s capabilities or just want to have some more fun, this upgrade is something you will use in a practical manner.

Subscribe
Notify of
guest

10 Comments
Newest
Oldest Most Voted
Inline Feedbacks
View all comments
Johnnie summers
Johnnie summers
3 months ago

Will the new switch fit in the stock switch location overhead next to the crawcontrol, will the wiring reach that far? All my dash switch holes are all taken up, no where to put this switch. Thanks.

Rob
Rob
3 months ago

Hey Johnnie 😊 Rob from BLACK OPS OFFROAD™ here. You definitely can fit the new OEM sized switch in the factory switch location. Check out the following link to Fred’s video on YouTube where he does exactly that – https://youtu.be/Kz2a0MEHjDY?si=1QZsmmwXLBQJAH8T …. Be sure to let us know if you have any other questions.

Chris Fortunato
Chris Fortunato
3 months ago

It is possible but I can’t confirm or deny if that location will work. All I know is wiring the switch over to the drivers side I had about 6” – 12” extra wire so you might be able to run the wire up the passenger side A-pillar to the roof.

Johnnie summers
Johnnie summers
3 months ago

Thank you . It would be something I would try.

eurowner
eurowner
3 months ago

it appears they, more or less, ripped off ExperiMental Designs system, which came out first and he worked very hard over the last few years to make it happen.

Chris Fortunato
Chris Fortunato
3 months ago
Reply to  eurowner

It’s not a rip off or an insult to ExperiMental, it’s just another brand making a similar product on the market. There’s been a desire for this mod for a while and companies are starting to make them this is just another company making a product to meet the demand of the consumer.

eurowner
eurowner
3 months ago

I hear you. It is very weird the timing after ExperiMentals system came out and proven by the buyers that the Ops systems come to market.

Scout
2 months ago
Reply to  eurowner

To my knowledge, this kit was originally developed overseas in Australia. It happened to be tested on a 3rd Gen, and it worked as well. It doesn’t seem anyone stole anything. And I believe Blackops owns the trademark for anytime locker as well… Either way, there’s a fine line with products like this. You could say someone took the design for window deflectors, sequential turn signals, low profile roof racks, hybrid front bumpers, modern shocks (the list goes on). If it’s not something wildly patentable and unique, it’s kind of fair game. I don’t mean to say this in a… Read more »

Scout
3 months ago

Killer post, Chris! For the longest time, there weren’t any options (outside of DIY – sketchy) where you could have this kind of override. Most people made it out to be too complicated. I’m glad that someone figured it out. Going to add this same kit to my truck. Great information. Also, way less intimidating than I thought it would be to install.

Chris Fortunato
Chris Fortunato
3 months ago

Thank you Konrad, I really appreciate the feedback!

10
0
Questions or Comments?x
()
x